How To

How To Create Epoxy Resin Festive/Winter Scenes:

How To Create Epoxy Resin Festive/Winter Scenes: - Craft Resin US

As we’re nearing the end of our Festive season Blogs this year we wanted to share more information about how to create beautiful Festive/Winter scenes like the project featured in the main image below:

 

 

 

You have your table set with beautiful Resin tablewares spread over it, you have your tree sparkling with all your tree decorations, now lets tackle the rest of the house and share how to create scenes that you could display anywhere in your home, or sell as part of your resin business each December!

 

Creating a festive scene can be a bit trickier than creating say a flat coaster type of resin design because of the 3D element to it, but that shouldn’t put you off, once you’ve read our guide you’ll be able to expand your resin skills and give these types of projects a go…

 

There are some molds on the market which will enable you to build your festive scene up in sections, this can be easier and save you using excess resin than pouring into one large mold. So browse the market and have a look at resin molds that come in sections that you can create then put together to create your finished scene.

 

Or you can attempt a thicker project, but you’ll need to create this in layers when using Craft Resin, as Craft Resin is designed as a coating resin, you can’t pour very large amounts all at once. But don’t worry, creating in layers may take more time overall, but it is very simple to do using the techniques below:

 

 

When it comes to building your resin projects up in layers you have two ways in which this can be done:

 

1 - Pour your first layer, wait a short while, then pour another.

 

Or

 

2 - Pour your first layer, wait till that’s cured, sand it down then pour another on top of that.

 

Let's go through the above steps in more details to teach you how to do this…

 

1 - Pour your first layer, wait a short while, then pour another:

 

Pour your first level as you normally would, remove any bubbles that form with your heat torch, then wait between 3-5 hours (the more times you create a project the better you’ll get at knowing how much time to leave it). 

 

Between 3-5 hours your resin won’t completely cure and will still be a thick, but not runny, semi-liquid state. You can pour another layer of resin mix onto this, get rid of any bubbles with a heat torch, and leave again for between 3-5 hours. Please ensure you set a timer so you don't go over this time.

 

 

To build up your project to reach its full height, simply repeat the steps above till the desired height is met. You can repeat this step as many times as you would like.

 

But you will need to increase your projected curing times to longer than 24-72 hours, depending on the thickness and how many layers you end up with. A thicker project will need to be kept in a warmer room to cure for much longer than 24 hours, sometimes even beyond a week or so.

 

We can’t tell you exactly how long this will take, because every project will be a different thickness so will need different curing times. Again the more you create and repeat a project the more you’ll build up the knowledge of your curing times.

 

If you are selling thicker projects to customers, then please make them aware before they purchase that the item will take longer to produce and it will take longer than normal to cure fully. This will set their expectations and will reduce your stress levels trying to get it to cure quicker!

 

2 - Pour your first layer, wait till that’s cured, sand it down then pour another on top of that:

 

The other option for layers is to pour your first 1/4” layer, use a heat torch to remove any bubbles, then leave this covered to fully cure.

 

 

Once this layer has cured you can use a sandpaper of between 80-120 grits to sand the top layer down, wiping clean any sanded grit from your project, ensuring your project is dry, before applying another layer of resin mix to this.

 

Again repeat the steps above till your resin project is at the desired height.

 

Both methods offer great options for building your projects up in layers. You may want to experiment by trying both to find the one that works best for yourself, with the particular thick projects that you will be creating.

 

Bubbles can be a bit trickier to get rid of in thicker projects, especially ones with items like flowers in. Pay attention to your work while it cures through each layer and then use our guidance on getting rid of bubbles to help combat these.

 

 

When creating a thicker project, you will potentially be using more resin mix than normal. Because of this you will need to be aware of the chemical reaction that happens when the resin and hardener are mixed called the exothermic reaction.

 

Exothermic reaction with thicker pours:

 

The exothermic reaction is the name of the chemical reaction that happens when the resin and hardener is mixed together, this reaction starts the curing process (hardening) off, a by product of this reaction is heat.

 

You’ll notice your mixing container getting warmer if you hold it while you mix your resin and hardener together, and when the resin is poured and left to cure it will get warmer still over the next few hours.

 

The more resin and hardener you mix together the more heat is generated, so you need to monitor this with thicker pours that require more resin mix and control it where possible.

 

 

If you don’t control the exothermic reaction this is when flash cures can happen, and can even cause your resin mix to give off smoke, a lot of heat and potentially even dangerous vapours. The heat given off in these extreme reactions can even cause nearby items to catch fire.

 

If you are going to be mixing larger amounts of epoxy resin together at once, then please make sure that you don’t preheat your resin in a warm sink of water before hand. Make sure that you mix slowly and for no longer than about 3-4 minutes.

 

This is also the only time that working in cooler environments would be more beneficial. Lower the temperature in your working and curing area to below 20C or 70F, and then increase the temperature back up towards the end of the cure, once the resin mix has cooled down more.

 

Following the steps above will also help, when you pour in layers you need to mix less resin mix at once, you also allow for the first layer to start cooling down before pouring the next, if not fully curing and cooling down all together with step 2.

 

You do need to be careful not to leave the gap between pouring your next layer too long though, after the 5 hour mark the next layer of resin mix may not join fully to the last one, or leave a line in your work where the two join because they haven’t fully bonded together.

 

Again some experimentation with timings may be needed to find your projects sweet spot.

 

 

If you are someone who creates a lot of thicker projects then please keep your eyes peeled on our Social Media channels early next year because we have something coming that you will absolutely love - But thats all we can say for now!

 

When it comes to creating winter/Festive scenes from resin again your choices of colours/glitters/additives will enable the project to look truly festive or not, so consider your colour choices when making these. Of course it can and will have your artistic flare in the project, so you can be fluid with this, any colour glitters we find make an item look more festive than block colours for example.

 

If you’re new to creating winter/festive scenes and you’d like some inspiration on what types of projects are out there like this that you can create, please visit our Instagram feed and have a browse. Many artists have been creating these types of projects recently, if you find one you’d like to try to create, reach out to the artist who is named in the text part of the post and ask them where they got their mold from. Most artists love sharing their knowledge with others so they will usually send you a link to where they purchased it.

 

Topic Of The Week Giveaway:

 

We have attached a giveaway to these Topic Of The Week announcements on our Instagram platform, this is helping us to spread the knowledge of how to use epoxy resin further, but also enabling anyone who helps us share this information to win free resin and mica powders.

 

 

To enter the weekly giveaway please see the latest post #CRWEEK51 on our Instagram feed/highlights and follow the instructions to enter:

 

@craft.resin

 

We can’t wait to see all your Festive Resin scenes all around your homes 🎉

 

Team Craft Resin

Reading next

Creating Festive Epoxy Resin Tableware This Christmas: - Craft Resin US
Reviewing Your 2022 Resin Creations/Business: - Craft Resin US